Integritas Beton Jembatan pada Kepulauan Bangka Belitung Berdasarkan Hasil UPV dan Rebound Hammer
DOI:
https://doi.org/10.58169/jusit.v4i2.1189Keywords:
Bridge Concrete, Concrete Quality, Non-Destructive, Rebound Hammer, Ultrasonic Pulse VelocityAbstract
This study was conducted to assess the condition and quality of concrete in bridges across the Bangka Belitung Islands Province using non-destructive methods: Ultrasonic Pulse Velocity (UPV), Rebound Hammer, and crack depth testing. This evaluation is crucial for determining the extent of concrete material degradation caused by factors such as structural age, environmental conditions, and construction quality, all of which can impact bridge performance. The research involved collecting field data from various structural elements—including girders, decks, piers, and abutments—and analyzing the results against BS 1881: Part 203:1986, ASTM C597-16, and SNI 2847:2019 standards. The findings indicate that UPV values ranged from 2,931 to 3,442 m/s, predominantly falling into the "medium" condition category. Estimated concrete compressive strength, based on the correlation between UPV and Rebound Hammer data, ranged from 15.60 to 33.12 MPa, with 64.29% of the bridges meeting the minimum standard of 21 MPa. Crack depth testing revealed depths ranging from 13 to 51 mm, mostly classified as shallow to medium. Overall, the combined use of UPV and Rebound Hammer methods provided complementary evaluation results regarding both internal and surface concrete quality. These findings suggest that while most bridges remain in serviceable condition, certain elements require further attention and maintenance to preserve their performance and service life.
References
Dzakiyyah, A. A., Santoso, A., & Pratama, R. (2026). Analisis perhitungan volume beton metode konvensional dan BIM Autodesk Revit pada proyek jembatan tipe lengkung terhadap efektivitas biaya. Jurnal Riset Rumpun Ilmu Teknik, 5(2), 65–78. https://doi.org/10.55606/jurritek.v5i2.9327
Habibbullah, M. N., Pratama, A., & Santoso, B. (2026). Penerapan BIM dalam perhitungan volume pekerjaan dan biaya konstruksi menggunakan software Autodesk Revit pada proyek Gedung Pengadilan Agama Sungai Raya. Jurnal Riset Rumpun Ilmu Teknik, 5(1), 12–25. https://doi.org/10.55606/jurritek.v5i1.7603
Hakiki, R., & Marpen, R. (2024). Analisis kekuatan struktur dan penurunan pondasi pada bangunan Masjid Asrama Haji Transit Kepulauan Bangka Belitung. Jurnal Gradasi Teknik Sipil, 8(2), 152–160. https://doi.org/10.31961/gradasi.v8i2.1456
Hakiki, R., & Raafidiani, R. (2020). Inspeksi kondisi dan penanganan jembatan di Pulau Nias Provinsi Sumatera Utara dengan metode Bridge Management System. Potensi: Jurnal Sipil Politeknik, 22(2), 156–168. https://doi.org/10.35313/potensi.v22i2.1862
Hanif, A., Kurniawandy, A., & Yusa, M. (2024). Evaluasi kuat tekan beton menggunakan UPV dan hammer test. SAINSTEK, 12(1), 135–140.
Hidayat, I., Rahardhani, A. F. S., & Suhardjo, G. A. (2024). Utilizing hammer tests and ultrasonic pulse velocity to ascertain the compressive strength of concrete. IOP Conference Series: Earth and Environmental Science, 1324(1), Article 012006. https://doi.org/10.1088/1755-1315/1324/1/012006
Ikhsan, S. (2023). Pengujian mutu beton Jembatan Voided Slab dengan metode hammer test. Prosiding FTSP Series, 73–76.
Kencanawati, N. N., Akmaluddin, Marlitasari, R., & Paedullah, G. (2021). Study on robustness of rebound hammer and ultrasonic pulse velocity measurement in several concrete damage levels. IOP Conference Series: Earth and Environmental Science, 708(1), Article 012069. https://doi.org/10.1088/1755-1315/708/1/012069
Nugroho, B. (2022). Evaluasi kuat tekan beton menggunakan hammer test dan ultrasonic pulse velocity (UPV) pada Jembatan Kuala Samboja. Jurnal Inersia, 14(1), 16–22. https://doi.org/10.46964/inersia.v14i1.361
Pappang, R. F., Santoso, D., & Pratama, R. (2024). Analisis hubungan nilai rebound Schmidt hammer dengan nilai uniaxial compressive strength (UCS) pada batupasir Formasi Balikpapan dan Pulaubalang. Venus: Jurnal Publikasi Rumpun Ilmu Teknik, 2(4), 180–192. https://doi.org/10.61132/venus.v2i4.415
Ridho, F., & Khoeri, H. (2015). Perbandingan mutu beton hasil UPVT metode indirect terhadap mutu beton hasil hammer test dan core drill. Konstruksia, 6(2).
Simatupang, R. M., Nuralinah, D., & Remayanti, C. (2016). Korelasi nilai kuat tekan beton antara hammer test, ultrasonic pulse velocity (UPV) dan compression test. Rekayasa Sipil, 10(1), 26–32.
Tumangger, R., Siregar, M., & Sembiring, J. (2026). Assesment schedule metode Defense Contract Management Agency (DCMA) menggunakan software Primavera P6 studi kasus proyek jembatan. ISAINTEK: Jurnal Informasi, Sains dan Teknologi, 9(1), 35–48. https://doi.org/10.55606/isaintek.v9i1.402
Tumingan, T., & Alwi, S. (2022). Kapasitas nilai kuat tekan beton dengan hammer test dan ultrasonic pulse velocity (UPV) Jembatan Loa Haur. Sebatik, 26(2), 582–592. https://doi.org/10.46984/sebatik.v26i2.2026
Yulian, A. E. (2018). Analisis kerapatan beton dengan menggunakan cepat rambat dan transmission time pada alat UPV (ultrasonic pulse velocity) [Karya ilmiah, Universitas Brawijaya].
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Jurnal Sipil Terapan

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.








